Chevrolet Sonic Repair Manual: Body
- General
- Body Hinge Pillar Lower Reinforcement Replacement
- Body Waterleak Repair
- Dimensions - Body (4NB)
- Dimensions - Body (5HB)
- Eliminating Unwanted Odors in Vehicles
- Front Hinge Pillar Body Sectioning
- General Plastic Repair
- How to Identify Plastic Parts
- Plastic Collar Quick Connect Fitting Service
- Plastic Collar Quick Connect Fitting Service
- Plastic Collar Quick Connect Fitting Service
- Plastic Identification and Refinishing Systems
- Rear Brake Hose Replacement (Body to Axle - Disc Brake)
- Rear Brake Hose Replacement (Body to Axle - Drum Brake)
- Body Electrical
- Doors and Enclosures
- Body Exterior
- Information
- Spoilers/Aero
- Bumpers
- Emblems/Decals/Paint
- Front Grille
- Garnish/Finishers/License
- Identification Plates
- Moldings
- Panels
- Trunk Bed
- Weatherstripping
- Frame and Structure
- Body Side Frame Rocker Reinforcement Replacement
- Driver or Passenger Seat Back Cushion Frame Replacement
- Driver or Passenger Seat Cushion Frame Replacement
- Drivetrain and Front Suspension Frame Replacement
- Front Compartment Front Insulator Cover Replacement
- Front Wheelhouse Liner Inner Front Extension Replacement (Left SIde)
- Front Wheelhouse Liner Inner Front Extension Replacement (Right SIde, LWE, LUW)
- Front Wheelhouse Liner Inner Front Extension Replacement (Right Side, LUV)
- Front Wheelhouse Liner Replacement (Front)
- Front Wheelhouse Liner Replacement (Rear)
- Rear Wheelhouse Liner Replacement (Hatchback - Left)
- Rear Wheelhouse Liner Replacement (Hatchback - Right)
- Rear Wheelhouse Liner Replacement (Sedan - Left)
- Rear Wheelhouse Liner Replacement (Sedan - Right)
- Rear Wheelhouse Panel Liner Extension Replacement
- Special Tools
- Center Pillar Reinforcement Replacement
- Drivetrain and Front Suspension Frame Skid Plate Replacement
- Glass & Windows
- Driver Info & Control
- Body Interior
- Arm Rests
- Center Console
- Cup Holders
- Dashboard Assembly
- Floorlining and Carpets
- Grab Handles
- Headlining
- Storage and Pockets
- Trim Panels/Welts
- Mirrors
- Mirror Adjustment
- Outside Mirror Description and Operation
- Inside Rearview Mirror Replacement
- Outside Rearview Mirror Glass Replacement
- Outside Rearview Mirror Housing Rear Cover Replacement
- Outside Rearview Mirror Housing Replacement
- Outside Rearview Mirror Motor Replacement
- Outside Rearview Mirror Remote Control Switch Replacement
- Outside Rearview Mirror Replacement (Manual)
- Outside Rearview Mirror Replacement (Power)
- Restraints
- Inflatable Restraint Sensing and Diagnostic Module Programming and Setup
- Primary
- Restraints Control
- Secondary
- Air Bag Modules
- Roof - Fixed, Leisure
- Airbag Roof Side Rail Module Replacement - Rear
- Roof Front Header Panel Replacement
- Roof Outer Panel Replacement (4NB)
- Roof Outer Panel Replacement (5HB)
- Roof Rail Front Assist Handle Replacement
- Roof Rail Rear Assist Handle Replacement
- Roof Rear Header Panel Replacement (5HB)
- Moonroof/Sunroof
- Roof Drainage
- Seating
- Wipers, Washers
Towing the Vehicle
Notice: Incorrectly towing a disabled vehicle may cause damage. The
damage would not be covered by the vehicle warranty. Do not lash or hook to
the chassis components including the front and ...
General
...
Other materials:
Emblem/Nameplate Replacement
Caution: Refer to Exterior Trim Emblem Removal Caution.
The part and vehicle surface should be 21?°C (70?°F) prior to installation.
The vehicle should remain inside in a temperature range of 21?°C (70?°F) for
1 hour after assembly to allow the adhesive to develop sufficient bo ...
Rear Compartment Lid Weatherstrip Replacement
Rear Compartment Lid Weatherstrip Replacement
Callout
Component Name
1
Rear Compartment Lid Weatherstrip
Procedure
Disconnect any electrical connector.
Clean the area where the seal will be mounted. Use a suit ...
Main Shaft Assemble (Gen 2)
Special Tools
3-0207944 Main Shaft Tapered Bearing Insert Tool
For equivalent regional tools, refer to Special Tools.
Install the 4th gear bearing assembly (1).
in!i.l.i-if
Note: The 3rd gear blocking ring lugs must be aligned with the
3rd/4th gear synchronizer ass ...
0.0149